12V Stainless Steel Hydraulic Power Pack for Clamping

Product Overview

The source states 0.75-1.5 kW power, customizable pressure with 7 MPa identified, 1400 RPM speed and a 6L tank. The catalog does not provide flow, cylinder size, port data or control logic, so buyers should supply required clamping force, movement time and pressure-holding behavior for review.

The unit is sold as a single item with a one-set minimum. A six-month warranty is stated. Buyers should capture selected voltage, power, pressure, tank, controls and mechanical interfaces in the final order rather than leave them as assumptions.

Technical Specifications

Key Features

• Purpose-Built Listing Context: Machine-tool clamping is named in both the title and the application attribute. That consistent positioning helps buyers identify the intended industrial context. Suitability still depends on the required clamping force and cycle, so provide cylinder dimensions, approach speed, hold time and release behavior when requesting a configuration.
• 12V DC Supply: The title specifies DC 12V for this hydraulic power pack. A 12V supply can involve substantial current depending on selected power, making electrical checks important. As general engineering guidance, verify supply capacity, voltage drop, cable size, switching and overcurrent protection for the proposed 0.75-1.5 kW version.
• Stainless Steel Material: Stainless steel is stated in the product title and source attributes. This is the material claim available for the unit; no grade, finish or environmental rating is given. Buyers with defined material or cleaning requirements should add them to the inquiry and obtain written confirmation for the offered construction.
• 6L Tank Capacity: A 6L tank is listed for this clamping power pack. The reservoir should be reviewed against total actuator displacement, return flow, heat and available installation space. The 6L figure is a documented product attribute, but it does not by itself establish suitability for every clamping cylinder or operating schedule.
• 7 MPa Pressure Reference: Pressure is marked customizable, with 7 MPa stated in the source. For a clamping application, calculate the pressure needed to produce the required force from the actual cylinder area. Then define normal pressure, hold requirements and relief setting so the proposed hydraulic and control arrangement can be reviewed without ambiguity.
• 1400 RPM Motor Speed: The listed speed is 1400 RPM and the power range is 0.75-1.5 kW. These values help frame the drive specification, but output flow also depends on pump displacement, which is not stated. Include the desired clamp approach and release times so flow can be addressed in the configuration discussion.

Applications

The source gives a clear application: powering the clamping cylinder of a machine tool. Related descriptions below remain within that purpose and the unit's documented 12V, pressure and reservoir characteristics:

• Machine-tool clamping cylinder systems
• 12V DC hydraulic clamping stations
• 7 MPa clamping power-pack inquiries
• Industrial fixtures using a 6L hydraulic tank

Selection Guide

Calculate required clamp force first, then use the cylinder area to determine operating pressure. Define approach, clamp, hold and release stages, including target times and cycle frequency. Compare the result with the listed customizable 7 MPa pressure, 0.75-1.5 kW power and 1400 RPM speed. Request flow and valve-circuit confirmation because those details are not included in the source record.

Verify that the 12V supply can support the selected motor and that a 6L tank is appropriate for actuator displacement and duty. General engineering guidance is to check voltage drop, protection, heat management, hose routing and maintenance access. If stainless grade, dimensions, mounting points or ports are important, include them as explicit approval items instead of relying on unspecified assumptions.

Ordering Information

The minimum order quantity is one set and the selling unit is one item. Submit the machine-tool application, 12V supply data, clamp force, cylinder details, required cycle, selected pressure, power and control sequence with the request. A six-month warranty is listed for this product; confirm its terms together with the 6L tank and complete approved configuration.

Frequently Asked Questions

Q: What application is stated for this power pack?

A: The source identifies the clamping cylinder of a machine tool as the application, matching the machine-tool clamping wording in the title.

Q: Is this a 12V hydraulic unit?

A: Yes. DC 12V is specified in the product title. Electrical capacity and protection should be checked for the selected motor power.

Q: What pressure and power are listed?

A: The source states customizable pressure with 7 MPa identified and a power range of 0.75-1.5 kW.

Q: What are the tank and speed values?

A: The listed tank capacity is 6L and the recorded speed is 1400 RPM. Required flow still needs separate confirmation.

Q: Is a single set available to order?

A: Yes. The MOQ is one set, sold as a single item, and this product states a six-month warranty.